Müller-ElektronikECU-Maxi controller
In stock
The Isobus-controller is prepared for the use on utility vehicles and machines. The communication with a virtual Terminal like Basic-Terminal, Basic-Terminal TOP or Comfort-Terminal runs on the standardized CAN network (ISO 11783). The Isobus-controller is equipped with a 16-bit CPU-card with flash memory. Software updates and configuration files can be downloaded across CAN.
Actuators and sensors are connected to one up to three 42-pin connectors via a cable loop, which consists of corrugated tubes. Diagnostic functions are available for all in- and outputs, which are protected against short circuits to ground or operating voltage. The electronic control unit II supplies the power for the sensors at the 42-pin connectors. All inputs for revolution sensors can be configured for sensors switching operating voltage or GND.
Technical data ECU-Maxi
| General: | |
| CPU: | Infenion C167CR 16 bit |
| Memory: | Flash 512 KiB; 2 RAM 32 KiB; 64 KiB I2C-Bus EEPROM |
| Connections: |
• Thread joint for cable with ISO-connector • 2 42-pin connectors (connector A & B, counterpart lockable and with separate seals for each wire to connect actuators and sensors) |
| Powersupply: | 10 VDC to 16 VDC or 19,2 VDC to 32 VDC (incl. Load-Dump protection up to 80 V) |
| Current (power on): | 400 mA (at 14,4 V without power output and power supply of external sensors) |
| Rest current (off): | 70 μA |
| Temperature range: | −20 °C to +70 °C (according to IEC68-2-14-Nb, IEC68-2-30 and IEC68-2-14Na) |
| Housing: | closed aluminum box, varnished aluminum top with gasket, stainless steel screws |
| Protection category: | IP66K (according to DIN40050 part9 1993) |
| Environmental test: | Vibration- and impact test according to IEC68-2 |
| Measurements: | 250 mm × 232 mm × 77 mm (without connector) |
| Weight: | 5,0 kg (with 6,5 m connection cable) |
|
|
| Base modul | |
| Connector A: | |
| Outputs: |
• 2 H-motorbridges for servomotors up to 12 A permanent current • 2 H-motorbridges for servomotors up to 4 A permanent, 6 A peak • 2 Power outputs up to 4 A permanent current • 1 Power output up to 2,5 A for magnetic or motorized valves (with own end switch off) |
| Inputs: |
• 7 Revolution- or analog Inputs • 9 Static- or analog Inputs • 2 Revolution inputs for operating voltage switching sensors |
|
|
| Connector B: | |
| Outputs: |
• 24 Power outputs up to 4 A (2 included for PWM use) • 1 Power outputs up to 8 A permanent current • 2 H-motorbridge for servomotors up to 4 A permanent, 6 A peak |
| Inputs: |
• 4 Power outputs up to 4 A permanent current or • 4 static or analog inputs |
|
|
| Add on cards (connector C): | |
| Connectors: |
• Internal socket on base modul • 1 42-pin connector (connector C, counterpart lockable and with separate seals for each wire to connect actuators and sensors) |
| Add on card outputs: | |
| Outputs: | • 15 Power outputs up to 2,5 A for magnetic or motorized valves (with own end switch off) |
| Inputs/Outputs: |
• 4 Power outputs up to 4 A permanent current or< • 4 Revolution inputs |
| Add on card inputs: | |
| Outputs: |
• 10 Power outputs up to 4 A • 2 H-motorbridge for servomotors up to 12 A permanent current |
| Inputs: | • 24 dynamic inputs |